Commercial MEP BIM Modeling & Shop Drawing Services
Commercial MEP BIM Modeling & Shop Drawing Services
Our commercial MEP BIM modeling services give mechanical, electrical, plumbing and fire protection trades a single, coordinated model to build from. We convert design drawings, RFIs and field conditions into detailed BIM models at LOD 300–400, giving contractors and engineers a clear, accurate picture of how every system fits together before work begins on site.
Coordination is where most commercial projects lose time and money, and it’s where we focus. Our team runs clash detection across all trades, resolves conflicts between ductwork, piping, conduit and structural elements, and works directly with your project team to keep the model current as changes come in. The result is a coordinated model that subcontractors and GCs can actually trust and build from.
From that coordinated model, we produce construction-ready shop drawings built for field installation — dimensioned, trade-specific, and aligned with the coordinated BIM model so there’s no gap between what’s modeled and what gets installed. Whether you’re a general contractor managing multiple trades or a subcontractor needing shop drawings for your scope, our goal is the same: fewer field conflicts, faster installation, and accurate as-builts you can rely on after the project closes out.
We provide commercial MEP BIM modeling and coordination for mechanical, electrical, plumbing and fire protection trades, converting design drawings into detailed, clash-free models at LOD 300–400. From that coordinated model, we deliver construction-ready shop drawings built for field installation — helping contractors and subcontractors avoid field conflicts, install faster, and finish with accurate as-builts.
Request a Quote
& Beyond
What You Receive
Coordinated Trade Models
Discipline models built from contract documents and design models to the LOD your BIM execution plan requires, in your templates and naming standards, ready to load into the project's federated model.
Clash Detection & Resolution
Clash runs, prioritized reports and worked resolutions carried through coordination meetings to sign-off — routing proposed and revised, not a raw clash list handed back for your team to solve.
Installation Shop Drawings
Dimensioned, sheeted installation drawings: plans, sections, details, elevations and equipment room layouts, referenced to project control and formatted to your drawing standards.
Fabrication & Spool Packages
Fabrication-level detail where the scope calls for it — spool drawings, hanger and support layouts, sleeve and penetration drawings, and cut information the shop can work from directly.
How We Work
Accurate installation drawings start with a model that has actually been coordinated. Our MEP shop drawing services carry the package from setup through to signed-off, sheeted drawings.
01
Scope & Setup
We review the contract documents, BIM execution plan, project standards and coordination schedule, then set the model up in your templates with the correct shared coordinates, naming and worksets.
02
Modeling & Detailing
Trade systems are modeled to the required level of development using real fittings, connection methods and installation practice — geometry a fabricator and a foreman can both work from.
03
Coordination & Clash Resolution
We run clashes, propose routing resolutions, support or attend coordination meetings, and revise the model through each round until the trade signs off.
04
Shop Drawing Production
Signed-off geometry is sheeted into dimensioned installation and fabrication drawings, issued in your formats, with revisions carried through as the job changes in the field.
Who This Is For
Commercial trade contractors across every MEP discipline use our MEP shop drawing services as production capacity they can turn on when a project demands it.
Mechanical & HVAC Contractors
Ductwork, hydronic and mechanical piping, equipment and mechanical room layouts, hangers, sleeves and penetrations — through to coordinated HVAC shop drawings and spool packages.
Electrical Contractors
Conduit and cable tray, power distribution and equipment layouts, lighting and device coordination, electrical room layouts, racks and supports — through to coordinated electrical shop drawings.
Plumbing Contractors
Domestic water, sanitary, vent and storm systems, fixture connections, risers and isometrics, equipment rooms, sleeves and penetrations — through to coordinated plumbing shop drawings.
Combined Mechanical & Plumbing
One contractor carrying both packages: shared mechanical rooms and ceiling space, common rack and hanger coordination, and a single production schedule across Mechanical and Plumbing.
Multi-Trade MEP Contractors
Multidiscipline modeling and coordination across all three trades under one production team, with consolidated model, revision and drawing management.
General Contractors & VDC Teams
Coordination support and subcontractor modeling capacity when a trade partner cannot produce the model the project schedule requires.